思科二层交换机+华为路由器配置单臂路由

admin

思科二层交换机+华为路由器配置单臂路由

思路：先创建VLAN；连接主机的接口配置为Access接口；连接华为路由器的接口配置为Trunk口。配置好设备名称，保存。

Switch>enable

Switch#configure terminal

Enter configuration commands, one per line.  End with CNTL/Z.

Switch(config)#vlan 100-102

Switch(config-vlan)#exit

Switch(config)#interface gigabitethernet 0/2

Switch(config-if)#switchport mode access

Switch(config-if)#switchport access vlan 101

Switch(config-if)#exit

Switch(config)#interface gigabitethernet 0/3

Switch(config-if)#switchport mode access

Switch(config-if)#switchport access vlan 102

Switch(config-if)#exit

Switch(config)#interface gigabitethernet 0/1

Switch(config-if)#switchport trunk encapsulation dot1q

Switch(config-if)#switchport mode trunk

Switch(config-if)#switchport trunk allowed vlan all

Switch(config-if)#exit

Switch(config)#hostname zurkjsw

zurkjsw#

zurkjsw#write

配置华为路由器

思路：1先配置连接思科交换机的接口（注意是配置为子接口，终结VLAN，并开启广播接口）。2配置DHCP服务。3配置设备名，保存。

<Huawei>system-view

[Huawei]sysname AR1   

[AR1]interface gigabitethernet 0/0/1.1

[AR1-GigabitEthernet0/0/0.1]ip address 172.16.101.1 24

[AR1-GigabitEthernet0/0/0.1]dot1q termination vid 101

[AR1-GigabitEthernet0/0/0.1]arp broadcast enable

[AR1-GigabitEthernet0/0/0.1]quit

[AR1]interface GigabitEthernet 0/0/1.2

[AR1-GigabitEthernet0/0/0.2]ip address 172.16.102.1 24

[AR1-GigabitEthernet0/0/0.2]dot1q termination vid 102  

[AR1-GigabitEthernet0/0/0.2]arp broadcast enable

[AR1-GigabitEthernet0/0/0.2]quit

[AR1]dhcp enable

[AR1]ip pool vlan101

[AR1-ip-pool-vlan101]gateway-list 172.16.101.1

[AR1-ip-pool-vlan101]network 172.16.101.0 mask 255.255.255.0

[AR1-…vlan101]excluded-ip-address 172.16.101.200172.16.102.254

[AR1-ip-pool-vlan101]dns-list 114.114.114.114 8.8.8.8

[AR1-ip-pool-vlan101]quit

[AR1]ip pool vlan102

[AR1-ip-pool-vlan102]gateway-list 172.16.102.1

[AR1-ip-pool-vlan102]network 172.16.102.0 mask 255.255.255.0

[AR1-…vlan102]excluded-ip-address 172.16.102.200172.16.102.254

[AR1-ip-pool-vlan102]dns-list 114.114.114.114 8.8.8.8

[AR1-ip-pool-vlan102]quit

[AR1]interface GigabitEthernet 0/0/1.1

[AR1-GigabitEthernet0/0/0.1]dhcp select global

[AR1-GigabitEthernet0/0/0.1]quit

[AR1]interface gigabitethernet 0/0/1.2

[AR1-GigabitEthernet0/0/0.2]dhcp select global

[AR1-GigabitEthernet0/0/0.2]quit

[AR1]interface loopback 0

[AR1-LoopBack0]ip address 100.100.100.100 32

[AR1-LoopBack0]quit